Craft Cut Create

Shopping Cart 0
$0.00
Welcome!

Services available for Mild Steel (A36/1008/A1018)

Bending

Freshly bent metal and plastic parts, straight from the machine to you.

Learn More
Hardware Insertion

Select from our catalog of PEM press-fit hardware to add nuts, studs, and standoffs.

Learn More
Plating

Boost rust prevention, enhance wear resistance, and strengthen your parts with zinc and nickel plating.

Learn More
Tapping

Quickly and easily add threading to allow for the addition of hardware to your parts.

Learn More
Powder Coating

Give your laser cut parts a bold, long-lasting finish and protective layer in one of 7 colors.

Learn More
Tumbling

Reduce the surface blemishes and handling scratches found in raw materials.

Learn More

Material Details

.030″ Mild Steel (A36/1008/A1018)

A1008 Mild Steel 0.030" General Details INCH MM
Advertised Thickness 0.030" 0.762 mm
Gauge 22 22
Thickness tolerance positive 0.003" 0.0762 mm
Thickness tolerance negative 0.003" 0.0762 mm
Mill Finish Cold Rolled Cold Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/- 0.030 per foot +/- 0.030 per foot
Min part size 0.25″ x 0.375″ 6.35 mm x 9.525 mm
Max part size 44″ x 30″ 1117.6 mm x 762 mm
Min hole size 0.015″ 0.381 mm
Min bridge size 0.015″ 0.381 mm
Min hole to edge distance 0.020″ 0.508 mm
Tab and slot tolerance .010" 0.254 mm
Bending Specifications INCH MM
Min bend part size 0.375" x 1.5" 9.525 mm x 38.1 mm
Max bending flat part size 44" x 30" 1117.6 mm x 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.255" 6.477 mm
Min flange length (after bend) 90° or less (obtuse) 0.286" 7.2644 mm
Minimum Length Center of bend line 91-130* (Acute) 0.344" 8.7376 mm
Die width 0.472" 11.9888 mm
Effective bend radius @ 90° 0.045" 1.143 mm
Max bend angle 130° 130°
Minimum bend angle 5° 5°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.061" 1.5494 mm
K Factor 0.38 0.38
Bend relief depth 0.095" 2.413 mm
Minimum joggle. Bend line to bend line @90° max flange 0.288" 7.3152 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Dimple Specifications: COMING SOON INCH MM
Min dimple part size 1.200" x 5.200" 30.48 mm x 132.08 mm
Max dimple part size 26" x 56" 660.4 mm x 1422.4 mm
Smallest dimple 0.500" 12.7 mm
Largest dimple 3.000" 76.2 mm
A1008 Mild Steel Properties INCH MM
Material Composition Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04 Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04
Density 490 lb/ft³ 490 lb/ft³
Heat treatments process N/A N/A
ASTM A1008-21A-CS-TYPE-B A1008-21A-CS-TYPE-B
Tensile Strength (Ultimate) 54 ksi 54 ksi
Tensile Strength (Yield) 45 ksi 45 ksi
Shear Strength 34 ksi 34 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 32 ksi 32 ksi
Brinell Hardness 100 100
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.048″ Mild Steel (A36/1008/A1018)

A1008 Mild Steel 0.048" General Details INCH MM
Advertised Thickness 0.048" 1.2192 mm
Gauge 18 18
Thickness tolerance positive 0.005" 0.127 mm
Thickness tolerance negative 0.004" 0.1016 mm
Mill Finish Cold Rolled Cold Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .25″ x .375″ 6.35 X 9.525 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .018″ 0.4572 mm
Min bridge size .024″ 0.6096 mm
Min hole to edge distance .020″ 0.508 mm
Tab and slot tolerance .010" 0.254 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.255" 6.477 mm
Min flange length (after bend) 90° or less (obtuse) 0.298" 7.5692 mm
Minimum Length Center of bend line 91-130* (Acute) 0.344" 8.7376 mm
Die width 0.472" 11.9888 mm
Effective bend radius @ 90° 0.045" 1.143 mm
Max bend angle 130° 130°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.086" 2.1844 mm
K Factor 0.36 9.144 mm
Bend relief depth 0.113" 2.8702 mm
Minimum joggle. Bend line to bend line @90° max flange 0.308" 7.8232 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Dimple Specifications: COMING SOON INCH MM
Min dimple part size 1.200" x 5.200" 30.48 X 132.08 mm
Max dimple part size 26" x 56" 660.4 X 1422.4 mm
Smallest dimple 0.500" 12.7 mm
Largest dimple 3.000" 76.2 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .425″ 10.795 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min Powder Coating Part Size 1" x 3" 25.4 X 76.2 mm
Max Powder Coating Part Size 23" x 23" 584.2 X 584.2 mm
A1008 Mild Steel Properties INCH MM
Material Composition Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04 Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04
Density 490 lb/ft^3 490 lb/ft^3
Heat treatments process N/A N/A
ASTM A1008-21A-CS-TYPE-B A1008-21A-CS-TYPE-B
Tensile Strength (Ultimate) 54 ksi 54 ksi
Tensile Strength (Yield) 45 ksi 45 ksi
Shear Strength 34 ksi 34 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 32 ksi 32 ksi
Brinell Hardness 100 100
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.059″ Mild Steel (A36/1008/A1018)

A1008 Mild Steel 0.059" General Details INCH MM
Advertised Thickness 0.059" 1.4986 mm
Gauge 16 16
Thickness tolerance positive 0.006" 0.1524 mm
Thickness tolerance negative 0.004" 0.1016 mm
Mill Finish Cold Rolled Cold Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .25" x .375" 635 X 9525 mm
Min hole size 0.022" 0.5588 mm
Min bridge size 0.030" 0.762 mm
Min hole to edge size 0.020" 0.508 mm
Tab and slot tolerance 0.010" 0.254 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.255" 6.477 mm
Min flange length (after bend) 90° or less (obtuse) 0.311" 7.8994 mm
Minimum Length Center of bend line 91-130* (Acute) 0.344" 8.7376 mm
Die width 0.472" 11.9888 mm
Effective bend radius @ 90° 0.063" 1.6002 mm
Max bend angle 130° 130°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.112" 2.8448 mm
K Factor 0.36 9.144 mm
Bend relief depth 0.142" 3.6068 mm
Minimum joggle. Bend line to bend line @90° max flange 0.320" 8.128 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Dimple Specifications: COMING SOON INCH MM
Min dimple part size 1.200" x 5.200" 30.48 X 132.08 mm
Max dimple part size 26" x 56" 660.4 X 1422.4 mm
Smallest dimple 0.500" 12.7 mm
Largest dimple 3.000" 76.2 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .441″ 11.2014 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap M3 x 0.5 M3 x 0.5
Smallest Tap M2 x 0.4 M2 x 0.4
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.030" 0.762 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.030" Tap hole size/2 +0.030
A1008 Mild Steel Properties INCH MM
Material Composition Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04 Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04
Density 490 lb/ft³ 490 lb/ft³
Heat treatments process N/A N/A
ASTM A1008-21A-CS-TYPE-B A1008-21A-CS-TYPE-B
Tensile Strength (Ultimate) 54 ksi 54 ksi
Tensile Strength (Yield) 45 ksi 45 ksi
Shear Strength 34 ksi 34 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 32 ksi 32 ksi
Brinell Hardness 100 100
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.074″ Mild Steel (A36/1008/A1018)

A1008 Mild Steel 0.074" General Details INCH MM
Advertised Thickness 0.074" 1.8796 mm
Gauge 14 14
Thickness tolerance positive 0.006" 0.1524 mm
Thickness tolerance negative 0.004" 0.1016 mm
Mill Finish Cold Rolled Cold Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .25″ x .375″ 6.35 X 9.525 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .028″ 0.7112 mm
Min bridge size .032″ 0.8128 mm
Min hole to edge distance .022″ 0.5588 mm
Tab and slot tolerance 0.010" 0.254 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.255" 6.477 mm
Min flange length (after bend) 90° or less (obtuse) 0.320" 8.128 mm
Minimum Length Center of bend line 91-130* (Acute) 0.344" 8.7376 mm
Die width 0.472" 11.9888 mm
Effective bend radius @ 90° 0.063" 1.6002 mm
Max bend angle 130° 130°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.129" 3.2766 mm
K Factor 0.4 10.16 mm
Bend relief depth 0.157" 3.9878 mm
Minimum joggle. Bend line to bend line @90° max flange 0.336" 8.5344 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Dimple Specifications: COMING SOON INCH MM
Min dimple part size 1.950" x 5.200" 49.53 X 132.08 mm
Max dimple part size 26" x 56" 660.4 X 1422.4 mm
Smallest dimple 1.000" 25.4 mm
Largest dimple 3.000" 76.2 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .448″ 11.3792 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap M6 x 1.0 M6 x 1.0
Smallest Tap M2 x 0.4 M2 x 0.4
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.037" 0.9398 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.037" Tap hole size/2 +0.037
A1008 Mild Steel Properties INCH MM
Material Composition Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04 Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04
Density 490 lb/ft³ 490 lb/ft³
Heat treatments process N/A N/A
ASTM A1008-21A-CS-TYPE-B A1008-21A-CS-TYPE-B
Tensile Strength (Ultimate) 54 ksi 54 ksi
Tensile Strength (Yield) 45 ksi 45 ksi
Shear Strength 34 ksi 34 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 32 ksi 32 ksi
Brinell Hardness 100 100
Elongation at Break 12% 12%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600°F 2600°F
Magnetic Yes Yes
Does it Rust Yes Yes

.104″ Mild Steel (A36/1008/A1018)

A1008 Mild Steel 0.104" General Details INCH MM
Advertised Thickness 0.104" 2.6416 mm
Gauge 12 12
Thickness tolerance positive 0.007" 0.1778 mm
Thickness tolerance negative 0.005" 0.127 mm
Mill Finish Cold Rolled Cold Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .25″ x .375″ 6.35 X 9.525 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .040″ 1.016 mm
Min bridge size .035″ 0.889 mm
Min hole to edge distance .031″ 0.7874 mm
Tab and slot tolerance .015" 0.381 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.368" 9.3472 mm
Min flange length (after bend) 90° or less (obtuse) 0.459" 11.6586 mm
Minimum Length Center of bend line 91-130* (Acute) .497" 12.6238 mm
Die width 0.630" 16.002 mm
Effective bend radius @ 90° 0.063" 1.6002 mm
Min bend angle 5° 5°
Max bend angle 130° 130°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.181" 4.5974 mm
K Factor 0.34 8.636 mm
Bend relief depth 0.187" 4.7498 mm
Minimum joggle. Bend line to bend line @90° max flange 0.482" 12.2428 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Dimple Specifications: COMING SOON INCH MM
Min dimple part size 2.450" x 5.200" 2.450 x 5.200
Max dimple part size 26" x 56" 660.4 X 1422.4 mm
Smallest dimple 1.250" 31.75 mm
Largest dimple 3.000" 76.2 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .451″ 11.4554 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap 1/4/2028 1/4/2028
Smallest Tap M2 x 0.4 M2 x 0.4
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 36" 914.4 X 914.4 mm
Tapping Min Hole to Edge 0.052" 1.3208 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.052" Tap hole size/2 +0.052
A1008 Mild Steel Properties INCH MM
Material Composition Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04 Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04
Density 490 lb/ft³ 490 lb/ft³
Heat treatments process N/A N/A
ASTM A1008-21A-CS-TYPE-B A1008-21A-CS-TYPE-B
Tensile Strength (Ultimate) 54 ksi 54 ksi
Tensile Strength (Yield) 45 ksi 45 ksi
Shear Strength 34 ksi 34 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 32 ksi 32 ksi
Brinell Hardness 100 100
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.119″ Mild Steel (A36/1008/A1018)

A1008 Mild Steel 0.119" General Details INCH MM
Advertised Thickness 0.119" 3.0226 mm
Gauge 11 11
Thickness tolerance positive 0.007" 0.1778 mm
Thickness tolerance negative 0.005" 0.127 mm
Mill Finish Cold Rolled Cold Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .25″ x .375″ 6.35 X 9.525 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .040″ 1.016 mm
Min bridge size .035″ 0.889 mm
Min hole to edge distance .036″ 0.9144 mm
Tab and slot tolerance .015" 0.381 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.368" 9.3472 mm
Min flange length (after bend) 90° or less (obtuse) 0.466" 11.8364 mm
Minimum Length Center of bend line 91-130* (Acute) 0.497" 12.6238 mm
Die width 0.630" 16.002 mm
Effective bend radius @ 90° 0.063" 1.6002 mm
Max bend angle 130° 130°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.196" 4.9784 mm
K Factor 0.38 9.652 mm
Bend relief depth 0.202" 5.1308 mm
Minimum joggle. Bend line to bend line @90° max flange 0.499" 12.6746 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Dimple Specifications: COMING SOON INCH MM
Min dimple part size 2.450" x 5.200" 2.450 x 5.200
Max dimple part size 26" x 56" 660.4 X 1422.4 mm
Smallest dimple 1.250" 31.75 mm
Largest dimple 3.000" 76.2 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .459″ 11.6586 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap 5/16/2024 5/16/2024
Smallest Tap M2 x 0.4 M2 x 0.4
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.060" 1.524 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.60" Tap hole size/2 +0.60
Tumble Specifications INCH MM
Min Part Size Tumbling 0.5″ x 1.5″ 12.7 x 38.1 mm
Max Part Size Tumbling 4″ x 7″ 101.6 x 177.8 mm
A1008 Mild Steel Properties INCH MM
Material Composition Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04 Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04
Density 490 lb/ft³ 490 lb/ft³
Heat treatments process N/A N/A
ASTM A1008-21A-CS-TYPE-B A1008-21A-CS-TYPE-B
Tensile Strength (Ultimate) 54 ksi 54 ksi
Tensile Strength (Yield) 45 ksi 45 ksi
Shear Strength 34 ksi 34 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 32 ksi 32 ksi
Brinell Hardness 100 100
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.135″ Mild Steel (A36/1008/A1018)

A1008 Mild Steel 0.135" General Details INCH MM
Advertised Thickness 0.135" 3.429 mm
Gauge 10 10
Thickness tolerance positive 0.006" 0.1524 mm
Thickness tolerance negative 0.006" 0.1524 mm
Mill Finish Cold Rolled Cold Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .25″ x .375″ 6.35 X 9.525 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .051″ 1.2954 mm
Min bridge size .055″ 1.397 mm
Min hole to edge distance .041″ 1.0414 mm
Tab and slot tolerance .010" 0.254 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.620" 15.748 mm
Min flange length (after bend) 90° or less (obtuse) 0.742" 18.8468 mm
Minimum Length Center of bend line 91-130° (Acute) 0.837" 21.2598 mm
Die width 0.984" 24.9936 mm
Effective bend radius @ 90° 0.100" 2.54 mm
Max bend angle 110° 110°
Minimum bend angle 5° 5°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.244" 6.1976 mm
K Factor 0.32 0.32
Bend relief depth 0.255" 6.477 mm
Minimum joggle. Bend line to bend line @90° max flange 0.769" 19.5326 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .488″ 12.3952 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap M10 x 1.5 M10 x 1.5
Smallest Tap M2 x 0.4 M2 x 0.4
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.068" 1.7272 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.068" Tap hole size/2 +0.068
Tumble Specifications INCH MM
Min Part Size Tumbling 0.5″ x 1.5″ 12.7 x 38.1 mm
Max Part Size Tumbling 4″ x 7″ 101.6 x 177.8 mm
A1008 Mild Steel Properties INCH MM
Material Composition Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04 Iron (Fe): 99.31 – 99.7 Manganese (Mn): 0.3 – 0.5 Carbon (C): 0 – 0.1 Sulfur (S): 0 – 0.05 Phosphorus (P): 0 – 0.04
Density 490 lb/ft³ 490 lb/ft³
Heat treatments process N/A N/A
ASTM A1008-21A-CS-TYPE-B A1008-21A-CS-TYPE-B
Tensile Strength (Ultimate) 54 ksi 54 ksi
Tensile Strength (Yield) 45 ksi 45 ksi
Shear Strength 34 ksi 34 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 32 ksi 32 ksi
Brinell Hardness 100 100
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.187″ Mild Steel (A36/1008/A1018)

A36 HRPO 0.187" General Details INCH MM
Advertised Thickness 0.187" 4.7498 mm
Gauge N/A N/A
Thickness tolerance positive 0.008" 0.2032 mm
Thickness tolerance negative 0.008" 0.2032 mm
Mill Finish Hot Rolled Pickled and Oiled Hot Rolled Pickled and Oiled
Steel Type HRP&O (typically dual certified ASTM A1018 CS Type B / for conversion to ASTM A36) HRP&O (typically dual certified ASTM A1018 CS Type B / for conversion to ASTM A36)
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .5″ x .570″ 12.7 X 14.478 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .070″ 1.778 mm
Min bridge size .073″ 1.8542 mm
Min hole to edge distance .056″ 1.4224 mm
Tab and slot tolerance .015" 0.381 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 44" 1117.6 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 0.620" 15.748 mm
Min flange length (after bend) 90° or less (obtuse) 0.781" 19.8374 mm
Min length center of bend line 91-130* (Acute) N/A N/A
Die width 0.984" 24.9936 mm
Effective bend radius @ 90° 0.125" 3.175 mm
Max bend angle 90° 90°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.323" 8.2042 mm
K Factor 0.36 9.144 mm
Bend relief depth 0.332" 8.4328 mm
Minimum joggle. Bend line to bend line @90° max flange 0.826" 20.9804 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .526″ 13.3604 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap 1/2/2020 1/2/2020
Smallest Tap M2 x 0.4 M2 x 0.4
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.094" 2.3876 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.094" Tap hole size/2 +0.094"
Tumble Specifications INCH MM
Min Part Size Tumbling 0.5″ x 1.5″ 12.7 x 38.1 mm
Max Part Size Tumbling 4″ x 7″ 101.6 x 177.8 mm
A36 HRPO Properties INCH MM
Material Composition Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280 Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280
Density 490 lb/ft³ 490 lb/ft³
Heat treatments process N/A N/A
ASTM A1011-18A-CS-TYPE B A1011-18A-CS-TYPE B
Tensile Strength (Ultimate) 69 ksi 69 ksi
Tensile Strength (Yield) 41 ksi 41 ksi
Shear Strength 44 ksi 44 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 29 ksi 29 ksi
Brinell Hardness 140 140
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.250″ Mild Steel (A36/1008/A1018)

A36 HRPO 0.250" General Details INCH MM
Advertised Thickness 0.250" 6.35 mm
Gauge N/A N/A
Thickness tolerance positive 0.008" 0.2032 mm
Thickness tolerance negative 0.008" 0.2032 mm
Mill Finish Hot Rolled Pickled and Oiled Hot Rolled Pickled and Oiled
Steel Type HRP&O (typically dual certified ASTM A1018 CS Type B / for conversion to ASTM A36) HRP&O (typically dual certified ASTM A1018 CS Type B / for conversion to ASTM A36)
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size .500″ x .750″ 12.7 X 19.05 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .095″ 2.413 mm
Min bridge size .125″ 3.175 mm
Min hole to edge distance .075″ 1.905 mm
Tab and slot tolerance .015" 0.381 mm
Bending Specifications INCH MM
Min bend part size .375" x 1.5" 9.525 X 38.1 mm
Max bending flat part size 44" x 30" 1117.6 X 762 mm
Max bend length 42" 1066.8 mm
Min flange length (before bend/Flat Pattern) 90° or less (obtuse) 1.150" 29.21 mm
Min flange length (after bend) 90° or less (obtuse) 1.361" 34.5694 mm
Min length center of bend line 91-130° (Acute) N/A N/A
Die width 1.575" 40.005 mm
Effective bend radius @ 90° 0.150" 3.81 mm
Max bend angle 90° 90°
Bend angle tolerance (bend length up to 24″) +/- 1 degree +/- 1 degree
Bend angle tolerance (bend length over 24″) +/- 2 degrees +/- 2 degrees
Bend deduction @ 90° 0.422" 10.7188 mm
K Factor 0.36 9.144 mm
Bend relief depth 0.420" 10.668 mm
Minimum joggle. Bend line to bend line @90° max flange 1.425" 36.195 mm
Maximum joggle. Bend line to bend line @90° max flange 3.750" 95.25 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) .564″ 14.3256 mm
Max 4 sided box flange height (hardware) 3" 76.2 mm
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap 1/2/2020 1/2/2020
Smallest Tap M2 x 0.4 M2 x 0.4
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.125" 3.175 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.125" Tap hole size/2 +0.125
Tumble Specifications INCH MM
Min Part Size Tumbling 0.5″ x 1.5″ 12.7 x 38.1 mm
Max Part Size Tumbling 4″ x 7″ 101.6 x 177.8 mm
A36 HRPO Properties INCH MM
Material Composition Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280 Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280
Density 490 lb/ft^3
490 lb/ft^3
Heat treatments process N/A N/A
ASTM A1011-18A-CS-TYPE B A1011-18A-CS-TYPE B
Tensile Strength (Ultimate) 69 ksi 69 ksi
Tensile Strength (Yield) 41 ksi 41 ksi
Shear Strength 44 ksi 44 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 29 ksi 29 ksi
Brinell Hardness 140 140
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.375″ Mild Steel (A36/1008/A1018)

A36 HR 0.375" General Details INCH MM
Advertised Thickness 0.375" 9.525 mm
Gauge N/A N/A
Thickness tolerance positive 0.040" 1.016 mm
Thickness tolerance negative 0.040" 1.016 mm
Mill Finish Hot Rolled Hot Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size 1.00″ x 1.00″ 25.4 X 25.4 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size .188″ 4.7752 mm
Min bridge size .160″ 4.064 mm
Min hole to edge distance .113″ 2.8702 mm
Tab and slot tolerance .050" 1.27 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) N/A N/A
Max 4 sided box flange height (hardware) N/A N/A
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap 1/2/2020 1/2/2020
Smallest Tap M6 x 1.0 M6 x 1.0
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.188" 4.7752 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.188" Tap hole size/2 +0.188
Tumble Specifications INCH MM
Min Part Size Tumbling 0.5″ x 1.5″ 12.7 x 38.1 mm
Max Part Size Tumbling 4″ x 7″ 101.6 x 177.8 mm
A36 HR Properties INCH MM
Material Composition Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280 Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280
Density 490 lb/ft^3 490 lb/ft^3
Heat treatments process N/A N/A
ASTM A1011-18A-CS-TYPE B A1011-18A-CS-TYPE B
Tensile Strength (Ultimate) 69 ksi 69 ksi
Tensile Strength (Yield) 41 ksi 41 ksi
Shear Strength 44 ksi 44 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 29 ksi 29 ksi
Brinell Hardness 140 140
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

.500″ Mild Steel (A36/1008/A1018)

A36 HR 0.500" General Details INCH MM
Advertised Thickness 0.500" 12.7 mm
Gauge N/A N/A
Thickness tolerance positive 0.050" 1.27 mm
Thickness tolerance negative 0.030" 0.762 mm
Mill Finish Hot Rolled Hot Rolled
Top/Bottom finish Identical both sides Identical both sides
Sourced from USA/Global USA/Global
Laser Cutting Specifications INCH MM
Cutting process Fiber laser Fiber laser
Cut tolerance +/- 0.005" 0.127 mm
Flatness tolerance before cutting +/-0.030 per foot +/-0.030 per foot
Min part size 1.00″ x 1.00″ 25.4 X 25.4 mm
Max part size 44″ x 30″ 1117.6 X 762 mm
Min hole size 0.190″ 4.826 mm
Min bridge size 0.170″ 4.318 mm
Min hole to edge distance 0.150″ 3.81 mm
Tab and slot tolerance .055" 1.397 mm
Hardware Specifications INCH MM
Min hardware part size 1″ x 1.5″ 25.4 X 38.1 mm
Max hardware part size 36″ x 46″ 914.4 X 1168.4 mm
Minimum distance from center of bend to center of hardware insertion hole (measured from flat pattern) N/A N/A
Max 4 sided box flange height (hardware) N/A N/A
Hardware specific specifications Please view our Hardware Catalog Please view our Hardware Catalog
Plating Specifications INCH MM
Min Plating Part Size 1″ x 3″ 25.4 X 76.2 mm
Max Plating Part Size 23″ x 23″ 584.2 X 584.2 mm
Powder Coating Specifications INCH MM
Min powder coating part size 1" x 3" 25.4 X 76.2 mm
Max powder coating part size 23" x 23" 584.2 X 584.2 mm
Tapping Specifications INCH MM
Largest Tap 1/2/2020 1/2/2020
Smallest Tap M6 x 1.0 M6 x 1.0
Min Flat Part Size Tapping 0.949" x 1.5" 24.1046 X 38.1 mm
Max Flat Part Size Tapping 36" x 46" 914.4 X 1168.4 mm
Tapping Min Hole to Edge 0.032" 0.8128 mm
Tapping Min Hole Center to Material Edge Tap hole size/2 +0.032" Tap hole size/2 +0.032
Tumble Specifications INCH MM
Min Part Size Tumbling 0.5″ x 1.5″ 12.7 x 38.1 mm
Max Part Size Tumbling 4″ x 7″ 101.6 x 177.8 mm
A36 HR Properties INCH MM
Material Composition Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280 Iron (Fe): 98.0 Manganese (Mn): 1.03 Carbon (C): 0.25 – 0.290 Copper (Cu): 0.20 Sulfur (S): .050 Phosphorus (P): 0.04 Silicon (Si): 0.280
Density 490 lb/ft^3 490 lb/ft^3
Heat treatments process N/A N/A
ASTM A1011-18A-CS-TYPE B A1011-18A-CS-TYPE B
Tensile Strength (Ultimate) 69 ksi 69 ksi
Tensile Strength (Yield) 41 ksi 41 ksi
Shear Strength 44 ksi 44 ksi
Shear Modulus 11000 ksi 11000 ksi
Fatigue Strength 29 ksi 29 ksi
Brinell Hardness 140 140
Elongation at Break 22% 22%
Elastic Modulus 27000 ksi 27000 ksi
Poisson’s Ratio 0.29 0.29
Thermal Conductivity 43 BTU/h-ft °F 43 BTU/h-ft °F
Melting Point 2600 °F 2600 °F
Magnetic Yes Yes
Does it Rust Yes Yes

Additional Charts and Guidelines

Min/Max Part Sizes

Processing Min/Max Part Sizes

Part Density Guidelines

Nesting Guidelines

Design Guidelines

Bending Deformation Guidelines

Hardware Catalog

Drill Size Reference Chart

Bending Calculator

3D file Guidelines
Frequently Asked Questions
What are the standard production times?

Your estimated shipping date is dynamically calculated in your shopping cart as you add parts and services. Generally, production times for standard orders, excluding additional services such as bending or finishing, range from 2-4 business days prior to shipping.

The cut tolerance varies by material and is influenced by both the cutting processused and the material's thickness. For detailed tolerance information for each material,please visit our Materials Library. Select the material you are interested in, navigate to the Material Details section, choose your desired thickness, and review the specific tolerance data provided.

Discounts based on quantity are automatically calculated during the quoting process. As you add parts to your cart, you'll notice discounts of 20% or more when you order two or more identical parts in most materials. For even more substantial savings, consider signing up for our mailing list to receive notifications about exclusive, limited-time offers!

At our facility, we accept orders ranging from a single piece . With no minimum order requirement, you can request precisely the number of parts your project requires.

If you're unable to select a material for your part, it's often due to the part size being either too large or too small for the available materials. Please verify that your design file is set up at a 1:1 scale and is in either inches or millimeters. After uploading your file, also ensure that the correct unit of measurement is selected to match your design specifications.

Start your first CraftCutCreate project today!

Upload your CAD design or utilize our parts builder to receive an instant complimentary quote on your bespoke laser-cut
parts, all conveniently delivered to your doorstep within days.

Upload Your File Build a Part
No CAD File? No Problem! Send your sketch or template to our Design Services team.
↑
Back to Top