Back to Top
Services available for 4130 Chromoly Steel
Plating
Boost rust prevention, enhance wear resistance, and strengthen your parts with zinc and nickel plating.
Learn More
Powder Coating
Enhance your laser-cut parts with a bold, durable finish and protective layer available in seven vibrant colors.
Learn More
Tumbling
Minimize surface imperfections and handling scratches commonly found in raw materials.
Learn MoreMaterial Details
.050" 4130 Chromoly Steel
- Laser Cutting View Specs
- Bending View Specs
- Plating View Specs
- Powder Coating View Specs
| 4130 Chromoly Steel .050" General Details | INCH | MM |
|---|---|---|
| Advertised Thickness | 0.050" | 1.27 mm |
| Gauge | N/A | N/A |
| Thickness tolerance positive | 0.003" | 0.076 mm |
| Thickness tolerance negative | 0.003" | 0.076 mm |
| Mill Finish | Hot Rolled Finished in Oil | Hot Rolled Finished in Oil |
| Top/Bottom finish | Identical both sides | Identical both sides |
| Sourced from | USA/Global | USA/Global |
| Laser Cutting Specification | INCH | MM |
| Cutting process | Fiber laser | Fiber laser |
| Cut tolerance +/- | 0.005" | 0.127 mm |
| Flatness tolerance before cutting | +/-0.030 per foot | +/-0.030 per foot |
| Min part size | .25″ x .375″ | 6.35 x 9.525 mm |
| Max part size | 44″ x 30″ | 1117.6 mm x 762 mm |
| Min hole size | .020″ | 0.508 mm |
| Min bridge size | .025″ | 0.635 mm |
| Min hole to edge distance | .020 | 0.508 mm |
 |
||
| Tab and slot tolerance | .010" | 0.254 mm |
 |
||
| Bending Specifications | INCH | MM |
| Min Bend Part Size | .375" x 1.5" | 9.525 mm x 38.1 mm |
| Max bending flat part size | 44″ x 30″ | 1117.6 x 762 mm |
| Max Bend Length | 44″ | 1117.6 mm |
| Min Flange Length (Before Bend/Flat Pattern) 90° or less (obtuse) | 0.255″ | 6.477 mm |
| Min Flange Length (After Bend) 90° or less (obtuse) | 0.303" | 7.696 mm |
| Minimum Length Center of bend line 91-130* (Acute) | 0.332" | 8.433 mm |
| Die Width | 0.472″ | 11.989 mm |
| Effective Bend Radius @ 90° | 0.050″ | 1.27 mm |
| Max Bend Angle | 130° | 130° |
| Bend angle tolerance (bend length up to 24″) | +/- 1 degree | +/- 1 degree |
| Bend angle tolerance (bend length over 24″) | +/- 2 degrees | +/- 2 degrees |
| Bend Deduction @ 90° | 0.095″ | 2.413 mm |
| K Factor | 0.38 | 0.38 |
| Bend Relief Depth | 0.120″ | 3.048 mm |
| Minimum Joggle Bend line to bend line @90° Max Flange | 0.310" | 7.874 mm |
| Maximum Joggle Bend line to bend line @90° Max Flange | 3.750″ | 95.25mm |
| Plating Specifications | INCH | MM |
| Min Plating Part Size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max Plating Part Size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| Powder Coating Specifications | INCH | MM |
| Min powder coating part size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max powder coating part size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| 4130 Chromoly Steel .050" Properties | INCH | MM |
| Material Composition | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 |
| Density | 490 lb/ft^3 | 490 lb/ft^3 |
| Heat treatments process | Annealed/spheroidized | Annealed/spheroidized |
| ASTM | A505/506 | A505/506 |
| Tensile Strength (Ultimate) | 77-150 ksi | 77-150 ksi |
| Tensile Strength (Yield) | 63-140 ksi | 63-140 ksi |
| Shear Strength | 49-93 ksi | 49-93 ksi |
| Shear Modulus | 11000 ksi | 11000 ksi |
| Fatigue Strength | 47-93 ksi | 47-93 ksi |
| Brinell Hardness | 135-140 | 135-140 |
| Elongation at Break | 15% | 15% |
| Elastic Modulus | 27000 ksi | 27000 ksi |
| Poisson’s Ratio | 0.29 | 0.29 |
| Thermal Conductivity | 26.5 BTU/h-ft °F | 26.5 BTU/h-ft °F |
| Melting Point | 2599 °F | 2599 °F |
| Magnetic | Yes | Yes |
| Does it Rust | Yes | Yes |
.063" 4130 Chromoly Steel
- Laser Cutting View Specs
- Bending View Specs
- Plating View Specs
- Powder Coating View Specs
| 4130 Chromoly Steel .063" General Details | INCH | MM |
|---|---|---|
| Advertised Thickness | 0.063" | 1.6 mm |
| Gauge | N/A | N/A |
| Thickness tolerance positive | 0.006" | 0.152 mm |
| Thickness tolerance negative | 0.006" | 0.152 mm |
| Mill Finish | Hot Rolled Finished in Oil | Hot Rolled Finished in Oil |
| Top/Bottom finish | Identical both sides | Identical both sides |
| Sourced from | USA/Global | USA/Global |
| Laser Cutting Specification | INCH | MM |
| Cutting process | Fiber laser | Fiber laser |
| Cut tolerance +/- | 0.005" | 0.127 mm |
| Flatness tolerance before cutting | +/-0.030 per foot | +/-0.030 per foot |
| Min part size | .25″ x .375″ | 6.35 x 9.525 mm |
| Max part size | 44″ x 30″ | 1117.6 mm x 762 mm |
| Min hole size | .030″ | 0.762 mm |
| Min bridge size | .032″ | 0.813 mm |
| Min hole to edge distance | .020 | 0.508 mm |
|
||
| Tab and slot tolerance | .010" | 0.254 mm |
|
||
| Bending Specifications | INCH | MM |
| Min Bend Part Size | .375" x 1.5" | 9.525 mm x 38.1 mm |
| Max bending flat part size | 44″ x 30″ | 1117.6 x 762 mm |
| Max Bend Length | 44″ | 1117.6 mm |
| Min Flange Length (Before Bend/Flat Pattern) 90° or less (obtuse) | 0.255″ | 6.477 mm |
| Min Flange Length (After Bend) 90° or less (obtuse) | 0.303" | 7.696 mm |
| Minimum Length Center of bend line 91-130* (Acute) | 0.332" | 8.433 mm |
| Die Width | 0.472″ | 11.989 mm |
| Effective Bend Radius @ 90° | 0.050″ | 1.27 mm |
| Max Bend Angle | 130° | 130° |
| Bend angle tolerance (bend length up to 24″) | +/- 1 degree | +/- 1 degree |
| Bend angle tolerance (bend length over 24″) | +/- 2 degrees | +/- 2 degrees |
| Bend Deduction @ 90° | 0.1065 | 2.705 mm |
| K Factor | 0.41 | 0.41 |
| Bend Relief Depth | 0.133″ | 3.378 mm |
| Minimum Joggle Bend line to bend line @90° Max Flange | 0.324" | 8.23 mm |
| Maximum Joggle Bend line to bend line @90° Max Flange | 3.750″ | 95.25mm |
| Plating Specifications | INCH | MM |
| Min Plating Part Size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max Plating Part Size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| Powder Coating Specifications | INCH | MM |
| Min powder coating part size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max powder coating part size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| 4130 Chromoly Steel .050" Properties | INCH | MM |
| Material Composition | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 |
| Density | 490 lb/ft^3 | 490 lb/ft^3 |
| Heat treatments process | Annealed/spheroidized | Annealed/spheroidized |
| ASTM | A505/506 | A505/506 |
| Tensile Strength (Ultimate) | 77-150 ksi | 77-150 ksi |
| Tensile Strength (Yield) | 63-140 ksi | 63-140 ksi |
| Shear Strength | 49-93 ksi | 49-93 ksi |
| Shear Modulus | 11000 ksi | 11000 ksi |
| Fatigue Strength | 47-93 ksi | 47-93 ksi |
| Brinell Hardness | 135-140 | 135-140 |
| Elongation at Break | 15% | 15% |
| Elastic Modulus | 27000 ksi | 27000 ksi |
| Poisson’s Ratio | 0.29 | 0.29 |
| Thermal Conductivity | 26.5 BTU/h-ft °F | 26.5 BTU/h-ft °F |
| Melting Point | 2599 °F | 2599 °F |
| Magnetic | Yes | Yes |
| Does it Rust | Yes | Yes |
.125" 4130 Chromoly Steel
- Bending View Specs
- Plating View Specs
- Powder Coating View Specs
- Tumbling View Specs
| 4130 Chromoly Steel .125" General Details | INCH | MM |
|---|---|---|
| Advertised Thickness | 0.125" | 3.175 mm |
| Gauge | N/A | N/A |
| Thickness tolerance positive | 0.009" | 0.229 mm |
| Thickness tolerance negative | 0.009" | 0.229 mm |
| Mill Finish | Hot Rolled Finished in Oil | Hot Rolled Finished in Oil |
| Top/Bottom finish | Identical both sides | Identical both sides |
| Sourced from | USA/Global | USA/Global |
| Laser Cutting Specification | INCH | MM |
| Cutting process | Fiber laser | Fiber laser |
| Cut tolerance +/- | 0.005" | 0.127 mm |
| Flatness tolerance before cutting | +/-0.030 per foot | +/-0.030 per foot |
| Min part size | .25″ x .375″ | 6.35 x 9.525 mm |
| Max part size | 44″ x 30″ | 1117.6 mm x 762 mm |
| Min hole size | .050″ | 1.27 mm |
| Min bridge size | .063″ | 1.6 mm |
| Min hole to edge distance | .038 | 0.965 mm |
|
||
| Tab and slot tolerance | .015" | 0.381 mm |
|
||
| Bending Specifications | INCH | MM |
| Min Bend Part Size | .375" x 1.5" | 9.525 mm x 38.1 mm |
| Max bending flat part size | 44″ x 30″ | 1117.6 x 762 mm |
| Max Bend Length | 40″ | 1016 mm |
| Min Flange Length (Before Bend/Flat Pattern) 90° or less (obtuse) | 0.620″ | 15.748 mm |
| Min Flange Length (After Bend) 90° or less (obtuse) | 0.723" | 18.364 mm |
| Minimum Length Center of bend line 91-130* (Acute) | 0.806" | 20.472 mm |
| Die Width | 0.984″ | 24.994 mm |
| Effective Bend Radius @ 90° | 0.090″ | 2.286 mm |
| Max Bend Angle | 130° | 130° |
| Bend angle tolerance (bend length up to 24″) | +/- 1 degree | +/- 1 degree |
| Bend angle tolerance (bend length over 24″) | +/- 2 degrees | +/- 2 degrees |
| Bend Deduction @ 90° | 0.205″ | 5.207 mm |
| K Factor | 0.43 | 0.43 |
| Bend Relief Depth | 0.235″ | 5.969 mm |
| Minimum Joggle Bend line to bend line @90° Max Flange | 0.758" | 19.253 mm |
| Maximum Joggle Bend line to bend line @90° Max Flange | 3.750″ | 95.25mm |
| Plating Specifications | INCH | MM |
| Min Plating Part Size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max Plating Part Size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| Powder Coating Specifications | INCH | MM |
| Min powder coating part size | 0.5″ x 1.5″ | 12.7 mm x 38.1 mm |
| Max powder coating part size | 4″ x 7″ | 101.6 mm x 177.8 mm |
| 4130 Chromoly Steel .125" Properties | INCH | MM |
| Material Composition | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 |
| Density | 490 lb/ft^3 | 490 lb/ft^3 |
| Heat treatments process | Annealed/spheroidized | Annealed/spheroidized |
| ASTM | A505/506 | A505/506 |
| Tensile Strength (Ultimate) | 77-150 ksi | 77-150 ksi |
| Tensile Strength (Yield) | 63-140 ksi | 63-140 ksi |
| Shear Strength | 49-93 ksi | 49-93 ksi |
| Shear Modulus | 11000 ksi | 11000 ksi |
| Fatigue Strength | 47-93 ksi | 47-93 ksi |
| Brinell Hardness | 135-140 | 135-140 |
| Elongation at Break | 15% | 15% |
| Elastic Modulus | 27000 ksi | 27000 ksi |
| Poisson’s Ratio | 0.29 | 0.29 |
| Thermal Conductivity | 26.5 BTU/h-ft °F | 26.5 BTU/h-ft °F |
| Melting Point | 2599 °F | 2599 °F |
| Magnetic | Yes | Yes |
| Does it Rust | Yes | Yes |
.190" 4130 Chromoly Steel
- Bending View Specs
- Plating View Specs
- Powder Coating View Specs
- Tumbling View Specs
| 4130 Chromoly Steel .190" General Details | INCH | MM |
|---|---|---|
| Advertised Thickness | 0.190" | 4.826 mm |
| Gauge | N/A | N/A |
| Thickness tolerance positive | 0.009" | 0.229 mm |
| Thickness tolerance negative | 0.009" | 0.229 mm |
| Mill Finish | Hot Rolled Finished in Oil | Hot Rolled Finished in Oil |
| Top/Bottom finish | Identical both sides | Identical both sides |
| Sourced from | USA/Global | USA/Global |
| Laser Cutting Specification | INCH | MM |
| Cutting process | Fiber laser | Fiber laser |
| Cut tolerance +/- | 0.005" | 0.127 mm |
| Flatness tolerance before cutting | +/-0.030 per foot | +/-0.030 per foot |
| Min part size | .500″ x .750″ | 12.7 mm x 19.05 mm |
| Max part size | 44″ x 30″ | 1117.6 mm x 762 mm |
| Min hole size | .070″ | 1.778 mm |
| Min bridge size | .070″ | 1.778 mm |
| Min hole to edge distance | .057 | 1.448 mm |
|
||
| Tab and slot tolerance | .015" | 0.381 mm |
|
||
| Bending Specifications | INCH | MM |
| Min Bend Part Size | .375" x 1.5" | 9.525 mm x 38.1 mm |
| Max bending flat part size | 44″ x 30″ | 1117.6 x 762 mm |
| Max Bend Length | 36″ | 914.4 mm |
| Min Flange Length (Before Bend/Flat Pattern) 90° or less (obtuse) | 0.620″ | 15.748 mm |
| Min Flange Length (After Bend) 90° or less (obtuse) | 0.782" | 19.863 mm |
| Minimum Length Center of bend line 91-130* (Acute) | N/A | N/A |
| Die Width | 0.984″ | 24.994 mm |
| Effective Bend Radius @ 90° | 0.125″ | 3.175 mm |
| Max Bend Angle | 90° | 90° |
| Bend angle tolerance (bend length up to 24″) | +/- 1 degree | +/- 1 degree |
| Bend angle tolerance (bend length over 24″) | +/- 2 degrees | +/- 2 degrees |
| Bend Deduction @ 90° | 0.324″ | 8.23 mm |
| K Factor | 0.37 | 0.37 |
| Bend Relief Depth | 0.335″ | 8.509 mm |
| Minimum Joggle Bend line to bend line @90° Max Flange | 0.829" | 21.057 mm |
| Maximum Joggle Bend line to bend line @90° Max Flange | 3.750″ | 95.25mm |
| Plating Specifications | INCH | MM |
| Min Plating Part Size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max Plating Part Size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| Powder Coating Specifications | INCH | MM |
| Min powder coating part size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max powder coating part size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| Tumble Specifications | INCH | MM |
| Min Part Size Tumbling | 0.5″ x 1.5″ | 12.7 mm x 38.1 mm |
| Max Part Size Tumbling | 4″ x 7″ | 101.6 mm x 177.8 mm |
| 4130 Chromoly Steel .190" Properties | INCH | MM |
| Material Composition | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 |
| Density | 490 lb/ft^3 | 490 lb/ft^3 |
| Heat treatments process | Annealed/spheroidized | Annealed/spheroidized |
| ASTM | A505/506 | A505/506 |
| Tensile Strength (Ultimate) | 77-150 ksi | 77-150 ksi |
| Tensile Strength (Yield) | 63-140 ksi | 63-140 ksi |
| Shear Strength | 49-93 ksi | 49-93 ksi |
| Shear Modulus | 11000 ksi | 11000 ksi |
| Fatigue Strength | 47-93 ksi | 47-93 ksi |
| Brinell Hardness | 135-140 | 135-140 |
| Elongation at Break | 15% | 15% |
| Elastic Modulus | 27000 ksi | 27000 ksi |
| Poisson’s Ratio | 0.29 | 0.29 |
| Thermal Conductivity | 26.5 BTU/h-ft °F | 26.5 BTU/h-ft °F |
| Melting Point | 2599 °F | 2599 °F |
| Magnetic | Yes | Yes |
| Does it Rust | Yes | Yes |
.250" 4130 Chromoly Steel
- Bending View Specs
- Plating View Specs
- Powder Coating View Specs
- Tumbling View Specs
| 4130 Chromoly Steel .250" General Details | INCH | MM |
|---|---|---|
| Advertised Thickness | 0.250" | 6.35 mm |
| Gauge | N/A | N/A |
| Thickness tolerance positive | 0.030" | 0.762 mm |
| Thickness tolerance negative | 0.010" | 0.554 mm |
| Mill Finish | Hot Rolled Finished in Oil | Hot Rolled Finished in Oil |
| Top/Bottom finish | Identical both sides | Identical both sides |
| Sourced from | USA/Global | USA/Global |
| Laser Cutting Specification | INCH | MM |
| Cutting process | Fiber laser | Fiber laser |
| Cut tolerance +/- | 0.005" | 0.127 mm |
| Flatness tolerance before cutting | +/-0.030 per foot | +/-0.030 per foot |
| Min part size | .500″ x .750″ | 12.7 mm x 19.05 mm |
| Max part size | 44″ x 30″ | 1117.6 mm x 762 mm |
| Min hole size | .100″ | 2.54 mm |
| Min bridge size | .125″ | 3.175 mm |
| Min hole to edge distance | .075 | 1.905 mm |
|
||
| Tab and slot tolerance | .035" | 0.889 mm |
|
||
| Bending Specifications | INCH | MM |
| Min Bend Part Size | .375" x 1.5" | 9.525 mm x 38.1 mm |
| Max bending flat part size | 44″ x 30″ | 1117.6 x 762 mm |
| Max Bend Length | 32″ | 812.8 mm |
| Min Flange Length (Before Bend/Flat Pattern) 90° or less (obtuse) | 1.150″ | 29.21 mm |
| Min Flange Length (After Bend) 90° or less (obtuse) | 1.367" | 34.722 mm |
| Minimum Length Center of bend line 91-130* (Acute) | N/A | N/A |
| Die Width | 1.575″ | 40.005 mm |
| Effective Bend Radius @ 90° | 0.170″ | 4.318 mm |
| Max Bend Angle | 90° | 90° |
| Bend angle tolerance (bend length up to 24″) | +/- 1 degree | +/- 1 degree |
| Bend angle tolerance (bend length over 24″) | +/- 2 degrees | +/- 2 degrees |
| Bend Deduction @ 90° | 0.434″ | 11.024 mm |
| K Factor | 0.36 | 0.36 |
| Bend Relief Depth | 0.440″ | 11.176 mm |
| Minimum Joggle Bend line to bend line @90° Max Flange | 1.425" | 36.195 mm |
| Maximum Joggle Bend line to bend line @90° Max Flange | 3.750″ | 95.25mm |
| Plating Specifications | INCH | MM |
| Min Plating Part Size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max Plating Part Size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| Powder Coating Specifications | INCH | MM |
| Min powder coating part size | 1″ x 3″ | 25.4 mm x 76.2 mm |
| Max powder coating part size | 23″ x 23″ | 584.2 mm x 584.2 mm |
| Tumble Specifications | INCH | MM |
| Min Part Size Tumbling | 0.5″ x 1.575″ | 12.7 mm x 38.1 mm |
| Max Part Size Tumbling | 4″ x 7″ | 101.6 mm x 177.8 mm |
| 4130 Chromoly Steel .050" Properties | INCH | MM |
| Material Composition | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 | Chromium (Cr): 0.8 – 1.1 Manganese (Mn): 0.4 – 0.6 Carbon (C): 0.28 – 0.33 Silicon (Si): 0.15 – 0.35 Molybdenum (Mo): 0.15 – 0.25 Sulfur (S): 0 – 0.040 Phosphorus (P): 0 – 0.035 |
| Density | 490 lb/ft^3 | 490 lb/ft^3 |
| Heat treatments process | Annealed/spheroidized | Annealed/spheroidized |
| ASTM | A505/506 | A505/506 |
| Tensile Strength (Ultimate) | 77-150 ksi | 77-150 ksi |
| Tensile Strength (Yield) | 63-140 ksi | 63-140 ksi |
| Shear Strength | 49-93 ksi | 49-93 ksi |
| Shear Modulus | 11000 ksi | 11000 ksi |
| Fatigue Strength | 47-93 ksi | 47-93 ksi |
| Brinell Hardness | 135-140 | 135-140 |
| Elongation at Break | 15% | 15% |
| Elastic Modulus | 27000 ksi | 27000 ksi |
| Poisson’s Ratio | 0.29 | 0.29 |
| Thermal Conductivity | 26.5 BTU/h-ft °F | 26.5 BTU/h-ft °F |
| Melting Point | 2599 °F | 2599 °F |
| Magnetic | Yes | Yes |
| Does it Rust | Yes | Yes |
Frequently Asked Questions
What are the standard production times?
Your estimated shipping date is dynamically calculated in your shopping cart as you add parts and services. Generally, production times for standard orders, excluding additional services such as bending or finishing, range from 2-4 business days prior to shipping.
What is your cut tolerance?
The cut tolerance varies by material and is influenced by both the cutting processused and the material's thickness. For detailed tolerance information for each material,please visit our Materials Library. Select the material you are interested in, navigate to the Material Details section, choose your desired thickness, and review the specific tolerance data provided.
How can I get a discount on my order?
Discounts based on quantity are automatically calculated during the quoting process. As you add parts to your cart, you'll notice discounts of 20% or more when you order two or more identical parts in most materials. For even more substantial savings, consider signing up for our mailing list to receive notifications about exclusive, limited-time offers!
What are the order limits for the number of parts?
At our facility, we accept orders ranging from a single piece . With no minimum order requirement, you can request precisely the number of parts your project requires.
Why am I unable to select a material for my project?
If you're unable to select a material for your part, it's often due to the part size being either too large or too small for the available materials. Please verify that your design file is set up at a 1:1 scale and is in either inches or millimeters. After uploading your file, also ensure that the correct unit of measurement is selected to match your design specifications.
Validate your login